Valves

• Optimum quality
• Durability
• Precise design

• NACE MR -01-75
• ASTM (Gr) Stainless steel, F316/316L carbon steel,A15 0/LF2 and duplex or super duplex Alloy (400,625,82, and C276)
• Heat Code for material traceable to EN10204.3.1B
• End connection optional for NPT (ASME B1.20.1)BSPP (ISO 228/1BS2779) BSPT (ISO 7.1/BS21) Socket weld (ASME B16.11) Butt Weld (ASME B- 16.25)
• Working pressure 10.000 (690 bar)
• Temperature up to 450°F (232°C) with PTFE packing up to 1200°F (648°C) with Grafoil® packing
• All valve 100% factory testing hydrostatically andpneum-atic leakage accordance with BS12266.1

• Single piece Body with Bonnet assembly
• End connection 1/8" to 2"
• PTEF or Graphite packing for bubble tight sealing
• Non- Rotating Tip to provide positive bubble- tight Metal to Metal Body/Bonnet seal
• 5mm or 10mm Orifice
• T bar Handle to operate
• Designed to comply with requirement of ANSI or ASME B 16.34
• Option valve bonnet assembly OS&Y Bolted anti-tamper and globe style assembly with non rotating needle trim

We procure finest quality metal from reliable vendors to develop the offered assortment of Y Strainer Valve. All our products are widely demanded by the customers for their high durability and long lasting features. Moreover, we ensure that quality-approved products are delivered at patrons premises within the stipulated time-period and in affordable prices.

Features:

• Best quality metal used
• Very long service life
• Handles extreme pressure and variable temperature
• Efficient
• Good durability
• Smooth operation

• Rugged construction
• Corrosion-resistance
• Durability

• 6000psi (414 bar)gas and super heated steam at 1,100°F (593°C)
• Excellent flow characteristics
• Allows streamlined flow
• Eliminates corrosion and deposits 6 0°incline pressure drop

• Tight shutoff
• Long valve life
• Prevents corruption
• Easy re-facing Positive seating function as standard
• Seat is guided at bottom and top Integral STELLITE Gr.6 deposited with specialized and automatic procedure which guarantees the achivement of stated constant characteristics
• The deep thickness of the deposited STELLITE Gr. enables many renewing operations of the seating surface

• Non-rotating solid cone eliminates galling
• Eliminates scoring or bending of the stem No torsion applied to gland packing
• Easy on site maintenance and low maintenance cost Low operational torque
• Can not be detached from the stem Close roundness and straightness tolerances
• Burnished for superior finish

• Graphoil as standard maximum temperature 650 degree C.
• Long operating life Prevents corruption

• Withstand high stresses caused by liveloading Bolt torques control total spring load Two sets of GLAND BUSHINGS maintain a minimum permanent stress of 4000psi on the graphite packing keeping it tight for long periods of time without maintenance

• A lantern ring and leak-off pipe provide detection or removal of leakage, if any, from the lower packing set

• Sealing effectiveness improves as overall packing length shortens.
• Chamber wall is burnishhed to a superior finish

• Of nodular cast iron Its form allows positive grip Impacted Hand-wheel is not necessary thanks to the two roller beatings.

• Well lubricated stem nut rotates on two thrust bearings 10,000 test cycles show no visible damage to parts Dust cover and sleeve protect stem threads from dirt, dust and sand

• STORAGE ON SITE Do not remove end protectors until ready to install Store valves indoors in a well- protected, dry area. Do not store in contact with the floor. Store on pallets or Shelves.

• Remove end protects when ready to install. Check nameplate to ensure correct type of valve. Valves should be partially open during welding. If the valve will be normally closed, piping should be flushed, the valve should then be operated 2-3 times before finally seating to prevent solid particle remaining between the seat and disc.

• Inspect periodically all critical parts for wear steam threads. Packing and packing glands. Body-bonnet joint and bolting seats.